/* Copyright (C) 1992, 1995, 1997, 1998, 1999 artofcode LLC.  All rights reserved.
  
  This program is free software; you can redistribute it and/or modify it
  under the terms of the GNU General Public License as published by the
  Free Software Foundation; either version 2 of the License, or (at your
  option) any later version.

  This program is distributed in the hope that it will be useful, but
  WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  General Public License for more details.

  You should have received a copy of the GNU General Public License along
  with this program; if not, write to the Free Software Foundation, Inc.,
  59 Temple Place, Suite 330, Boston, MA, 02111-1307.

*/

/*$Id: scf.h,v 1.2.6.1.2.1 2003/01/17 00:49:05 giles Exp $ */
/* Common definitions for CCITTFax encoding and decoding filters */

#ifndef scf_INCLUDED
#  define scf_INCLUDED

#include "shc.h"

/*
 * The CCITT Group 3 (T.4) and Group 4 (T.6) fax specifications map
 * run lengths to Huffman codes.  White and black have different mappings.
 * If the run length is 64 or greater, two or more codes are needed:
 *      - One or more 'make-up' codes for 2560 pixels;
 *      - A 'make-up' code that encodes the multiple of 64;
 *      - A 'termination' code for the remainder.
 * For runs of 63 or less, only the 'termination' code is needed.
 */

/* ------ Encoding tables ------ */

/*
 * The maximum possible length of a scan line is determined by the
 * requirement that 3 runs have to fit into the stream buffer.
 * A run of length N requires approximately ceil(N / 2560) makeup codes,
 * hence 1.5 * ceil(N / 2560) bytes.  Taking the largest safe stream
 * buffer size as 32K, we arrive at the following maximum width:
 */
#if arch_sizeof_int > 2
#  define cfe_max_width (2560 * 32000 * 2 / 3)
#else
#  define cfe_max_width (max_int - 40)	/* avoid overflows */
#endif
/* The +5 in cfe_max_code_bytes is a little conservative. */
#define cfe_max_code_bytes(width) ((width) / 2560 * 3 / 2 + 5)

typedef hce_code cfe_run;

/* Codes common to 1-D and 2-D encoding. */
/* The decoding algorithms know that EOL is 0....01. */
#define run_eol_code_length 12
#define run_eol_code_value 1
extern const cfe_run cf_run_eol;
typedef struct cf_runs_s {
    cfe_run termination[64];
    cfe_run make_up[41];
} cf_runs;
extern const cf_runs
      cf_white_runs, cf_black_runs;
extern const cfe_run cf_uncompressed[6];
extern const cfe_run cf_uncompressed_exit[10];	/* indexed by 2 x length of */

			/* white run + (1 if next run black, 0 if white) */
/* 1-D encoding. */
extern const cfe_run cf1_run_uncompressed;

/* 2-D encoding. */
extern const cfe_run cf2_run_pass;

#define cf2_run_pass_length 4
#define cf2_run_pass_value 0x1
#define cf2_run_vertical_offset 3
extern const cfe_run cf2_run_vertical[7];	/* indexed by b1 - a1 + offset */
extern const cfe_run cf2_run_horizontal;

#define cf2_run_horizontal_value 1
#define cf2_run_horizontal_length 3
extern const cfe_run cf2_run_uncompressed;

/* 2-D Group 3 encoding. */
extern const cfe_run cf2_run_eol_1d;
extern const cfe_run cf2_run_eol_2d;

/* ------ Decoding tables ------ */

typedef hcd_code cfd_node;

#define run_length value

/*
 * The value in the decoding tables is either a white or black run length,
 * or a (negative) exceptional value.
 */
#define run_error (-1)
#define run_zeros (-2)	/* EOL follows, possibly with more padding first */
#define run_uncompressed (-3)
/* 2-D codes */
#define run2_pass (-4)
#define run2_horizontal (-5)

#define cfd_white_initial_bits 8
#define cfd_white_min_bits 4	/* shortest white run */
extern const cfd_node cf_white_decode[];

#define cfd_black_initial_bits 7
#define cfd_black_min_bits 2	/* shortest black run */
extern const cfd_node cf_black_decode[];

#define cfd_2d_initial_bits 7
#define cfd_2d_min_bits 4	/* shortest non-H/V 2-D run */
extern const cfd_node cf_2d_decode[];

#define cfd_uncompressed_initial_bits 6		/* must be 6 */
extern const cfd_node cf_uncompressed_decode[];

/* ------ Run detection macros ------ */

/*
 * For the run detection macros:
 *   white_byte is 0 or 0xff for BlackIs1 or !BlackIs1 respectively;
 *   data holds p[-1], inverted if !BlackIs1;
 *   count is the number of valid bits remaining in the scan line.
 */

/* Aliases for bit processing tables. */
#define cf_byte_run_length byte_bit_run_length_neg
#define cf_byte_run_length_0 byte_bit_run_length_0

/* Skip over white pixels to find the next black pixel in the input. */
/* Store the run length in rlen, and update data, p, and count. */
/* There are many more white pixels in typical input than black pixels, */
/* and the runs of white pixels tend to be much longer, so we use */
/* substantially different loops for the two cases. */

#define skip_white_pixels(data, p, count, white_byte, rlen)\
BEGIN\
    rlen = cf_byte_run_length[count & 7][data ^ 0xff];\
    if ( rlen >= 8 ) {		/* run extends past byte boundary */\
	if ( white_byte == 0 ) {\
	    if ( p[0] ) { data = p[0]; p += 1; rlen -= 8; }\
	    else if ( p[1] ) { data = p[1]; p += 2; }\
	    else {\
		while ( !(p[2] | p[3] | p[4] | p[5]) )\
		    p += 4, rlen += 32;\
		if ( p[2] ) {\
		    data = p[2]; p += 3; rlen += 8;\
		} else if ( p[3] ) {\
		    data = p[3]; p += 4; rlen += 16;\
		} else if ( p[4] ) {\
		    data = p[4]; p += 5; rlen += 24;\
		} else /* p[5] */ {\
		    data = p[5]; p += 6; rlen += 32;\
		}\
	    }\
	} else {\
	    if ( p[0] != 0xff ) { data = (byte)~p[0]; p += 1; rlen -= 8; }\
	    else if ( p[1] != 0xff ) { data = (byte)~p[1]; p += 2; }\
	    else {\
		while ( (p[2] & p[3] & p[4] & p[5]) == 0xff )\
		    p += 4, rlen += 32;\
		if ( p[2] != 0xff ) {\
		    data = (byte)~p[2]; p += 3; rlen += 8;\
		} else if ( p[3] != 0xff ) {\
		    data = (byte)~p[3]; p += 4; rlen += 16;\
		} else if ( p[4] != 0xff ) {\
		    data = (byte)~p[4]; p += 5; rlen += 24;\
		} else /* p[5] != 0xff */ {\
		    data = (byte)~p[5]; p += 6; rlen += 32;\
		}\
	    }\
	}\
	rlen += cf_byte_run_length_0[data ^ 0xff];\
    }\
    count -= rlen;\
END

/* Skip over black pixels to find the next white pixel in the input. */
/* Store the run length in rlen, and update data, p, and count. */

#define skip_black_pixels(data, p, count, white_byte, rlen)\
BEGIN\
    rlen = cf_byte_run_length[count & 7][data];\
    if ( rlen >= 8 ) {\
	if ( white_byte == 0 )\
	    for ( ; ; p += 4, rlen += 32 ) {\
		if ( p[0] != 0xff ) { data = p[0]; p += 1; rlen -= 8; break; }\
		if ( p[1] != 0xff ) { data = p[1]; p += 2; break; }\
		if ( p[2] != 0xff ) { data = p[2]; p += 3; rlen += 8; break; }\
		if ( p[3] != 0xff ) { data = p[3]; p += 4; rlen += 16; break; }\
	    }\
	else\
	    for ( ; ; p += 4, rlen += 32 ) {\
		if ( p[0] ) { data = (byte)~p[0]; p += 1; rlen -= 8; break; }\
		if ( p[1] ) { data = (byte)~p[1]; p += 2; break; }\
		if ( p[2] ) { data = (byte)~p[2]; p += 3; rlen += 8; break; }\
		if ( p[3] ) { data = (byte)~p[3]; p += 4; rlen += 16; break; }\
	    }\
	rlen += cf_byte_run_length_0[data];\
    }\
    count -= rlen;\
END

#endif /* scf_INCLUDED */